Home Tournaments Calendar Weather Merchandise Sponsors

Go Back   Spearboard.com - The World's Largest Spearfishing Diving Boating Social Media Forum > United States Geographical Locations > California Off-Topic

California Off-Topic Remember that politics/religion and general off-topic belong in Special Forums.

Reply
 
Thread Tools Rate Thread Display Modes
Old 07-15-2019, 08:29 PM   #31
Diver278
Registered User
 
Diver278's Avatar
 
Join Date: Sep 2011
Location: San Diego,Ca / Dapitan, PI
Posts: 408
Re: Kimera slip tip

I shoot a 85cm and 115cm pathos rollers.
Diver278 is offline   Reply With Quote
Old 07-18-2019, 03:30 PM   #32
PigStikr
Stupendous User
 
Join Date: Apr 2007
Posts: 473
Re: Kimera slip tip

Quote:
Originally Posted by Mana'squal View Post
Slip tip is solid. Only gripe is the line they give you is shit. I might crimp stiff spectra to replace it or something.
I use 1/16" 7-strand stainless cable. Unwind the end leaving 3 and 4 on a side. Push each end thru the eye in opposite directions. Then wind the cable back together until hitting the fork. Then wind the remainder into a small pigtail and put a crimp over the pigtail end to keep it from unraveling. You can't tell that it was ever taken apart and it is much easier/thinner than splicing. Here is a video of winding a large cable. The thin stuff doesn't have a fiber core and I don't double braid the tail or put a nut on the end like they do. I just wind up a single pigtail and put a 1/16" ID crimp tube over it and crimp.

https://youtu.be/jsfll_7CdEQ
__________________

Last edited by PigStikr; 07-18-2019 at 03:59 PM.
PigStikr is offline   Reply With Quote
Old 07-20-2019, 08:39 AM   #33
Mana'squal
Registered User
 
Mana'squal's Avatar
 
Join Date: Jul 2016
Location: North East US
Posts: 307
Re: Kimera slip tip

Quote:
Originally Posted by PigStikr View Post
I use 1/16" 7-strand stainless cable. Unwind the end leaving 3 and 4 on a side. Push each end thru the eye in opposite directions. Then wind the cable back together until hitting the fork. Then wind the remainder into a small pigtail and put a crimp over the pigtail end to keep it from unraveling. You can't tell that it was ever taken apart and it is much easier/thinner than splicing. Here is a video of winding a large cable. The thin stuff doesn't have a fiber core and I don't double braid the tail or put a nut on the end like they do. I just wind up a single pigtail and put a 1/16" ID crimp tube over it and crimp.

https://youtu.be/jsfll_7CdEQ


I donít care for cable. Our fish donít justify the need. Went with stiff dynema. Testing today

Click image for larger version

Name:	IMG_2109.jpg
Views:	54
Size:	53.0 KB
ID:	243507Click image for larger version

Name:	IMG_2108.jpg
Views:	52
Size:	66.6 KB
ID:	243508
Mana'squal is offline   Reply With Quote
Old 07-20-2019, 08:41 AM   #34
Mana'squal
Registered User
 
Mana'squal's Avatar
 
Join Date: Jul 2016
Location: North East US
Posts: 307
Re: Kimera slip tip

Other upgrade I did was drilling a shaft to barely fit a flopper pin. I donít care for the thing they provide. Prefer a flopper pin bent in a slight crescent shape
Mana'squal is offline   Reply With Quote
Old 07-29-2019, 03:13 AM   #35
PigStikr
Stupendous User
 
Join Date: Apr 2007
Posts: 473
Re: Kimera slip tip

Quote:
Originally Posted by Mana'squal View Post
I donít care for cable. Our fish donít justify the need. Went with stiff dynema. Testing today
Looks nice! I use cable mainly because it is much thinner and thus can penetrate thru thicker fish without as much friction. The crimp around the single 'tag end' vs. both cables after weaving is also much thinner.
__________________
PigStikr is offline   Reply With Quote
Old 07-29-2019, 02:52 PM   #36
makemwearit
Desert Fish in da Pacific
 
Join Date: Mar 2017
Posts: 36
Re: Kimera slip tip

Quote:
Originally Posted by Mana'squal View Post
Other upgrade I did was drilling a shaft to barely fit a flopper pin. I donít care for the thing they provide. Prefer a flopper pin bent in a slight crescent shape
Noticed that. Both pins for both tips (7mm & 8mm) they sent with mine were too loose and I used a bit of epoxy to keep them in place instead of the superglue they provided. Included spectra was clearly lower quality and started to wear quickly.

Have only gotten to test it on big calicos so far, but the Customer Service I received from Kimera after USPS "lost" my first order was beyond disappointing (IMO based on my interactions with the Kimera team I don't believe it was actually ever sent). Took over a month to get my order and I'm located in CA where they're based out of.
__________________
Spearo Aquaholic
Bay Area
makemwearit is offline   Reply With Quote
Old 07-29-2019, 02:57 PM   #37
Mana'squal
Registered User
 
Mana'squal's Avatar
 
Join Date: Jul 2016
Location: North East US
Posts: 307
Re: Kimera slip tip

Quote:
Originally Posted by makemwearit View Post
Noticed that. Both pins for both tips (7mm & 8mm) they sent with mine were too loose and I used a bit of epoxy to keep them in place instead of the superglue they provided. Included spectra was clearly lower quality and started to wear quickly.



Have only gotten to test it on big calicos so far, but the Customer Service I received from Kimera after USPS "lost" my first order was beyond disappointing (IMO based on my interactions with the Kimera team I don't believe it was actually ever sent). Took over a month to get my order and I'm located in CA where they're based out of.


Took them 3 weeks to get me a package that weighs less then an ounce. Itís certainly okay, but I think they have a lot to improve on. As I use this more Iím not as enthusiastic about this tip. I placed a perfect shot on a striped bass 34-38Ē fish in the 20# range from 4í out. Fish came off. I am 99% it was a tip malfunction that cost me that fish.
Mana'squal is offline   Reply With Quote
Old 07-30-2019, 02:31 AM   #38
PigStikr
Stupendous User
 
Join Date: Apr 2007
Posts: 473
Re: Kimera slip tip

I have used Biller slip tips on fish to around 4 feet long, specifically the PK-312 mounted on a regular spear rather than on a pole spear. The solid slip tip slips off after penetrating and is held by the stainless cable, not a flimsy flopper pin. The other real advantage is that the fish is held by the cable with the tip at 90 degrees. Thus the spear is no longer in the fish and won't get bent.

Is in this image:
http://www.abbiller.com/wp-content/t...ccessories.png

Available here:
http://www.abbiller.com/products/pole-spears/

Depending on your spear shaft thread, you may have to use the regular speargun tip, the ST-312:
http://www.abbiller.com/wp-content/t..._shaft-tip.png
__________________

Last edited by PigStikr; 07-30-2019 at 02:45 AM.
PigStikr is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:26 PM.


The World's Largest Spearfishing Diving Social Media Forum Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©2002 - 2014 Spearboard.com