Home Tournaments Calendar Weather Merchandise Sponsors

Go Back   Spearboard.com - The World's Largest Spearfishing Diving Boating Social Media Forum > Spearfishing Gear > Non-Gun DIY Projects and Customizations

Non-Gun DIY Projects and Customizations This section is for your DIY spearfishing projects and customization other then spearguns.

Reply
 
Thread Tools Rate Thread Display Modes
Old 09-26-2018, 07:45 AM   #1
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Big Fish Cooler Modifications

I run a 22ft panga offshore and regularly bring in fish over 50". Since I have no fish hold, I use a 150qt cooler. I had a cheap Coleman for a while but it didn't hold ice well and it was always breaking latches and hinges. I debated getting a rotomolded cooler, but the fact that is would weigh 70lbs unloaded ruled that out. I ended up purchasing an Igloo maxcold 150 for $95 on ebay and adding a few features that I like from the higher end coolers. List of parts follows:
Cooler: $95
Rubber Feet: $10
Rubber Latches: $15
Marine Epoxy: $5
Total: $125

Process:
There isn't much to this project. My biggest concern is getting good connections between the ad on parts. I used a small predrilled hole for each screw and then loaded up every contact area with the epoxy. I even removed the stock screw in hinges and set them all in epoxy to reinforce them. Note that one nice feature on this cooler is that is does not have any straps to hold the cooler open. The hinges are oversized and stop the lid from opening too far. Ill add pictures from my computer.
SJ_Spearo is offline   Reply With Quote
Old 09-26-2018, 07:54 AM   #2
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Re: Big Fish Cooler Modifications

Here is the stock cooler. I was really impressed by how rugged this cooler seemed. It has nice thick walls and the lid does not deform when you sit or stand on it. The lid fits snug in place and seems to make a good seal. The hinges are oversized and have stronger plastic that will be more difficult for the screws to pull out of.
Attached Thumbnails
Click image for larger version

Name:	42521703_1840294519395870_2638160567528849408_n.jpg
Views:	830
Size:	27.7 KB
ID:	239869   Click image for larger version

Name:	42526369_2133156860048434_8058511034266157056_n.jpg
Views:	803
Size:	22.2 KB
ID:	239870   Click image for larger version

Name:	42482617_1959062500782338_4026806550403219456_n.jpg
Views:	825
Size:	27.6 KB
ID:	239871  
SJ_Spearo is offline   Reply With Quote
Old 09-26-2018, 07:57 AM   #3
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Re: Big Fish Cooler Modifications

Here are the modifications. Took about 1.5 hrs to get everything set in place. Hopefully my connections are strong enough to hold up to some abuse. All hardware is stainless steels so it wont corrode.
Attached Thumbnails
Click image for larger version

Name:	42551903_340411986534890_1045230473879486464_n.jpg
Views:	826
Size:	147.9 KB
ID:	239872   Click image for larger version

Name:	42572377_314324659346058_4013319210632478720_n.jpg
Views:	825
Size:	150.6 KB
ID:	239873   Click image for larger version

Name:	42549072_1932990023677448_8553177866743840768_n.jpg
Views:	829
Size:	155.7 KB
ID:	239874   Click image for larger version

Name:	42591563_547162375739397_2083308680454864896_n.jpg
Views:	815
Size:	148.1 KB
ID:	239875  
SJ_Spearo is offline   Reply With Quote
Old 09-26-2018, 08:02 AM   #4
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Re: Big Fish Cooler Modifications

My challenge right now is to find a way to secure the cooler to the vertical bulkhead of the casting deck (see picture). I want to keep all hardware off the deck of the boat and make the cooler easy to connect and disconnect so I can slide it out of the way to access that front hatch. Let me know if you guys have any ideas.
Attached Thumbnails
Click image for larger version

Name:	22281791_367861146984087_5744164158980832715_n.jpg
Views:	842
Size:	75.2 KB
ID:	239876  
SJ_Spearo is offline   Reply With Quote
Old 09-30-2018, 06:00 PM   #5
dr.ed
Registered User
 
dr.ed's Avatar
 
Join Date: Jan 2007
Location: West Virginia
Age: 79
Posts: 1,047
Re: Big Fish Cooler Modifications

Quote:
Originally Posted by SJ_Spearo View Post
My challenge right now is to find a way to secure the cooler to the vertical bulkhead of the casting deck (see picture). I want to keep all hardware off the deck of the boat and make the cooler easy to connect and disconnect so I can slide it out of the way to access that front hatch. Let me know if you guys have any ideas.
I suggest that you epoxy nylon loops to each side of bulkhead (port & starboard) approximately one half the cooler height. Then use a cam-lock strap through the loops to hold the cooler in place at the bow. Maybe two sets. If you epoxy the loops a couple of inches less than the width of cooler, the cam-lock straps will tension the cooler in place.
dr.ed is offline   Reply With Quote
Old 10-02-2018, 09:09 AM   #6
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Re: Big Fish Cooler Modifications

That's a good idea. I'm going to experiment with something similar, but with rubber straps today. Ideally, i'd like it to snap in place with spring clips and not require any adjustment.
SJ_Spearo is offline   Reply With Quote
Old 10-02-2018, 10:41 AM   #7
2fishin2
Pacific Spearo
 
Join Date: Jul 2007
Age: 63
Posts: 3,358
Re: Big Fish Cooler Modifications

Industrial strength velcro
2fishin2 is offline   Reply With Quote
Old 10-03-2018, 02:39 PM   #8
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Re: Big Fish Cooler Modifications

Here's what I came up with. Taking the boat out this weekend so I'll see how it works.
Attached Thumbnails
Click image for larger version

Name:	20181002_155330.jpg
Views:	853
Size:	64.0 KB
ID:	240029   Click image for larger version

Name:	20181002_155423.jpg
Views:	844
Size:	95.9 KB
ID:	240030  
SJ_Spearo is offline   Reply With Quote
Old 10-03-2018, 02:40 PM   #9
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Re: Big Fish Cooler Modifications

Not sure if I like how it's attached to the lid, but I can deal change that later. The S hooks are not stainless so I will need to replace them. Just looking for proof of concept really.
SJ_Spearo is offline   Reply With Quote
Old 10-03-2018, 08:46 PM   #10
los mentirosos
Dave Mote
 
los mentirosos's Avatar
 
Join Date: Jul 2006
Location: Corpus Christi
Posts: 518
Re: Big Fish Cooler Modifications

36" stainless steel piano hinge from big box store. The factory hinges suck .
__________________
When Guns are Outlawed
Only Outlaws will have Guns
los mentirosos is offline   Reply With Quote
Old 10-03-2018, 11:51 PM   #11
2fishin2
Pacific Spearo
 
Join Date: Jul 2007
Age: 63
Posts: 3,358
Re: Big Fish Cooler Modifications

Like I said before industrial strength velcro strips. No corrosion, no noise, no damage and will last forever.
2fishin2 is offline   Reply With Quote
Old 10-08-2018, 07:08 AM   #12
SJ_Spearo
Registered User
 
SJ_Spearo's Avatar
 
Join Date: Aug 2013
Location: Clarksville, TN
Age: 31
Posts: 393
Re: Big Fish Cooler Modifications

The current setup worked pretty well for an offshore trip recently. I'll probably run with it for a while. Only issue I had was that the melted ice was sloshing and coming through around the lid. Anyone ever use rtv or something to make a watertight gasket?
SJ_Spearo is offline   Reply With Quote
Old 10-08-2018, 07:33 AM   #13
2fishin2
Pacific Spearo
 
Join Date: Jul 2007
Age: 63
Posts: 3,358
Re: Big Fish Cooler Modifications

Quote:
Originally Posted by SJ_Spearo View Post
The current setup worked pretty well for an offshore trip recently. I'll probably run with it for a while. Only issue I had was that the melted ice was sloshing and coming through around the lid. Anyone ever use rtv or something to make a watertight gasket?
The lid is made to fit body with minimal of difference. If you try to make a gasket, it might just make it worse.

Last edited by 2fishin2; 10-08-2018 at 07:48 AM.
2fishin2 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:21 PM.


The World's Largest Spearfishing Diving Social Media Forum Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2002 - 2014 Spearboard.com